EBC Premium Rear Rotors 13+ Ford F350 (inc Super Duty) 6.2 DRW 2WD

EBC Premium Brake Rotors

EBC manufacture the vast majority of its automotive rotors including
Premium brake rotors in the UK or Europe.

EBC then adds value to its products by strictest quality controls and specifications and a 100% run out and dimensional check, including element analysis, surface finish and hardness tests on every batch and runout inspection . All sport rotors are slotted and grooved at the Las Vegas facility of the USA operation or at our new Northampton rotor facility employing 32 staff which has recently been enhanced to have its own QC department, machining and testing facilities and a new Nitrotherm anti corrosion coating plant.

We also do all we can to embrace US employment and in our US facilities we employ 14 people in our rotor machining facility alone.

Product Information:

EBC Automotive brake rotors are made from G3000 spec cast iron and full specifications and properties can be seen here!

Runout figures above this will lead to vibration after 3000 to 4000 miles due to what we call disc thickness variation (wearing a thin spot on the high point of the rotor as it runs off-true) which is not a warranty condition.

So you see this is no cheap import brake disc. These brake discs have the highest integrity and product quality on the aftermarket. An OE quality replacement disc, made of the finest grade iron and a perfect replacement disc for any car.

Every EBC rotor is runout inspected on this machine. Even when manufactured on state of the art precision machines, not even ONE single disc escapes this process guaranteeing perfect disc alignment. If during install you notice runout on your car it will surely be due to a chassis alignment that happens on one in seven cars, usually cased by nudging a kerb or hitting a pothole in the road earlier in driving the vehicle.

Statement of Quality:

CORRECTING ROTOR DISTORTION, ROTOR MISALIGNMENT AND CURE BRAKE VIBRATION

There are two main reasons for brake vibration. The first is steering geometry issues and the second is installation or hub run-out issues.

GEOMETRY ISSUES - One in seven cars suffers geometry problems during its life that can affect steering and cause brake vibration. These are NOT a product quality issue!!!!!!.These can happen by simply nudging a kerb or by driving over a pothole. EBC is not alone in recognising this problem but is the only brake supplier on the planet prepared to offer diagnosis and a SOLUTION.

INSTALLATION OR HUB RUN-OUT ISSUES - These cause what is known as DTV. The videos below show how to correct for brake vibration caused by DTV (Disc thickness variation). DTV develops in a car after 3000-4000 miles caused by runout built in to the car or due to incorrect alignment of the rotors at install. This is quite a common fault on modern cars and many cars require this at every rotor change. Drivers also confuse hub distortion with a rotor quality issue but in 99% of cases the DTV is a car problem, not a rotor quality problem. You can replace the rotors as many times as you like trying to solve vibration and the problem will only go away for a few thousand miles and then return. This means you have purchased new rotors in good faith but the problem is not solved and will not go away permanently until you perform this procedure. After this skimming of the rotor surface you will have smooth brakes , more effective brakes and zero vibration. It is even a very worthwhile practice when fitting new rotors to have all four rotors skimmed into perfect alignment on your car with this inexpensive procedure. Rotor distortion due to DTV is very common, in fact one in seven cars has a steering geometry problem either when it is built NEW or after nudging a kerb or hitting a large pothole (very common after road surface damage after winter snowy periods). Uneducated people still say "My rotors are warped". Well the engineering facts are rotors do not warp, they are made of cast iron, they are very tough and can be run to red heat and cooled time after time and they will not distort, we do this day in day out on our dynos in the EBC lab. Thats why the whole world still uses cast iron as a vehicle brake rotor material, there has never been anything to beat it and probably never will be. Pro Cut machines Work on both plain rotors and even better on slotted and drilled rotors of all types.

Vehicle Fitments: