{"product_id":"pdm15-solid-state-power-distribution-management-main-unit","title":"Wiring Specialties SR20DET Harness Kit Swap HW-PDM15","description":"\u003cp\u003ePDM 15  A PDM (Power Distribution Module) is a device used to replace conventional relays and fuses in a vehicle electrical system. The PDM takes inputs from physical switches, analogue voltages, or the CAN bus, and provides power to different electronic devices such as radiator fans, fuel pumps and head lights. The current being drawn from each connected device is continuously monitored. If the measured current is too high due to a fault, the PDM switches off the respective output to prevent further damage to the wiring loom or the connected device. The PDM can then retry the output to see if the fault has cleared. Product Details Included\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003ePDM15 Main Unit Technical Specification Advantages Over Fuses and Relays\u003c\/li\u003e\n\u003cli\u003eGreatly simplifies system wiring and reduces system component count.\u003c\/li\u003e\n\u003cli\u003eReduces the weight of the electrical system.\u003c\/li\u003e\n\u003cli\u003eProvides increased reliability over traditional systems using mechanical relays.\u003c\/li\u003e\n\u003cli\u003eSolid state technology removes the problem of relay contact corrosion and relay bouncing in vibration heavy applications.\u003c\/li\u003e\n\u003cli\u003eSmart features such as indicator and wiper motor modes remove the need for extra control units.\u003c\/li\u003e\n\u003cli\u003eCurrent draw can be monitored and logged to pre-emptively detect faults.   General Features\u003c\/li\u003e\n\u003cli\u003eSize: 200x160x54mm\u003c\/li\u003e\n\u003cli\u003eWeight: 615g\u003c\/li\u003e\n\u003cli\u003eOperating Temperature: -55°C to 90°C (-67°F to 194°F)\u003c\/li\u003e\n\u003cli\u003eConstruction: Glass Fibre Reinforced Plastic\u003c\/li\u003e\n\u003cli\u003eIP Rating: IP67\u003c\/li\u003e\n\u003cli\u003eConnectors: Deutsch DT 12-Pin\u003c\/li\u003e\n\u003cli\u003eUpdate Rate: Up to 800Hz   Inputs\u003c\/li\u003e\n\u003cli\u003eType: 16 Analogue inputs, which can also serve as digital inputs\u003c\/li\u003e\n\u003cli\u003eMeasurement Range: Each input can measure between 0V-6V\u003c\/li\u003e\n\u003cli\u003eMeasurement Resolution: 10-Bit, or 0.01V\u003c\/li\u003e\n\u003cli\u003eProtection: Fully protected for input voltages from -24V to 40V\u003c\/li\u003e\n\u003cli\u003eAdded Features: Current sourcing for ground switch detection. Configure as active high or low. Configurable Hysteresis voltage. Latching or momentary operation.   Outputs\u003c\/li\u003e\n\u003cli\u003eType: 15 High side outputs 80A peak, 20A continuous.\u003c\/li\u003e\n\u003cli\u003eCombined: 180A combined output maximum current\u003c\/li\u003e\n\u003cli\u003eOutput Current Control Steps: 100mA (0.1A)\u003c\/li\u003e\n\u003cli\u003eProtection: Each output is overcurrent, overtemperature, load dump and reverse polarity protected.\u003c\/li\u003e\n\u003cli\u003e5V: One 5V, 500mA output for supplying external sensors\/Hardwire Electronics CAN Keypad\u003c\/li\u003e\n\u003cli\u003eAdded Features: Outputs can be configured to stay on for a specified time after the input is removed, useful for thermo-fans. Outputs can be retried multiple times after an over-current event is detected.   Data Logging\u003c\/li\u003e\n\u003cli\u003eStorage: 128Mb of onboard flash storage for logging PDM data\u003c\/li\u003e\n\u003cli\u003eSpeed: 0.1Hz to 50Hz\u003c\/li\u003e\n\u003cli\u003eViewing: Data can be downloaded and graphed via the Hardwire Electronics PDM configurator software   Functions\u003c\/li\u003e\n\u003cli\u003eOutput Functions: Each Output can be switched with a user defined function\u003c\/li\u003e\n\u003cli\u003eLogical Operators: AND, OR, NOR, XOR, NAND, NOR, \u0026gt;, \u0026gt;=, \u0026lt;, \u0026lt;=, Equal, Not Equal   USB\u003c\/li\u003e\n\u003cli\u003eType: USB 2.0 Compliant Mini-B\u003c\/li\u003e\n\u003cli\u003eDriver: Integrated driver for Windows 10   CAN Bus\u003c\/li\u003e\n\u003cli\u003eInterface: 1x CAN2.0A\/B\u003c\/li\u003e\n\u003cli\u003eBus Speed: 50kbps, 100kbps, 125kbps, 250kbps, 500kbps, 1000kbps\u003c\/li\u003e\n\u003cli\u003eInput Stream: 40 Inputs, fully customizable variable parsing with bit masking and math functions. A range of CAN config files are available to communicate with common ECUs.\u003c\/li\u003e\n\u003cli\u003eOutput Stream: 15 Outputs, fully customizable CAN frame construction with math functions\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Wiring Specialties","offers":[{"title":"Default Title","offer_id":48086472523928,"sku":"9HVCI","price":849.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0564\/0867\/0360\/files\/wiring-specialties-sr20det-main_947510b7-1ad0-4694-8d27-45825f31d493.png?v=1771299267","url":"https:\/\/frsport.com\/products\/pdm15-solid-state-power-distribution-management-main-unit","provider":"FR SPORT","version":"1.0","type":"link"}